GreenPAK™ SLG47105-EV Development Kit with Socket Adapter
The SLG47105EV-SKT is a socket adapter kit for use with the SLG4DVKADV GreenPAK Advanced Development Board or SLG4DVKLITE GreenPAK Lite Development Board. The...
Overview
Description
The SLG47105-EV provides a small, low power component for commonly used mixed-signal and bridge functions. The user creates their circuit design by programming the one-time programmable (OTP) non-volatile memory (NVM) to configure the interconnect logic, the IO pins, the high-voltage pins, and the macrocells of the SLG47105-EV. Configurable PWM macrocells in combination with special high-voltage outputs will be useful for motor drive or load drive applications. High-voltage pins allow for the design of smart level translators or for driving the high-voltage high-current load.
Features
- 2 power supply inputs:
- 2.5V (±8%) to 5.0V (±10%) VDD
- 3.3V (±9%) to 12.0V (±10%) VDD2
- 4 high-voltage high-current drive GPOs
- Dual/Single full-bridge driver option
- Quad/Dual/Single half-bridge driver option
- Slew rate modes:
- Motor driver mode
- Pre-driver (MOSFET driver) mode
- Sleep function
- Low RDS(ON) high-side + low-side resistance = 0.4Ω typical
- 2A peak, 1.5A RMS per full bridge (at VDD2 = 5V, TA = 25 °C)
- 4A peak, 3A RMS per two full bridge connected in parallel (at VDD2 = 5V, TA = 25 °C)
- 2A peak, 1.5A RMS per half bridge GPO (at VDD2 = 5V, TA = 25 °C)
- Integrated overcurrent (OCP), short circuit, undervoltage-lockout (UVLO), thermal shutdown (TSD) protections
- SENSE_A, SENSE_B inputs that are connected to the current comparators for current control
- Fault signal indicator (OCP/UVLO/TSD)
- Differential amplifier with integrator and comparator for motor speed control function
- 2 current sense comparators with dynamical Vref mode
- 2 high-speed general-purpose ACMPs
- Modes: UVLO, OCP, TSD, voltage monitor, current monitor
- 1 voltage reference (Vref) output
- 5 multi-function macrocells
- 4 selectable DFF/LATCH/3-bit LUTs + 8-bit delay/counters
- 1 selectable DFF/LATCH/4-bit LUT + 16-bit delay/counter
- 12 combination function macrocells
- 3 selectable DFF/LATCH or 2-bit LUTs
- 1 selectable programmable pattern generator or 2-bit LUT
- 6 selectable DFF/LATCH or 3-bit LUTs
- 1 selectable pipe delay or ripple counter or 3-bit LUT
- 1 selectable DFF/LATСH or 4-bit LUT
- 2 PWM macrocells
- Flexible 8-bit/7-bit PWM mode with the duty cycle control
- 16 preset duty cycle registers switching mode for PWM Sine or other waveforms
- Serial communications
- I2C protocol interface
- Programmable delay with edge detector output
- Additional logic function – One deglitch filter with edge detectors
- 2 oscillators (OSC)
- 2.048kHz oscillator
- 25MHz oscillator
- Analog temperature sensor with ACMP connected output
- Power-on Reset (POR)
- One-time programmable memory
- Operating temperature range: -40 °C to 105 °C
- RoHS compliant/Halogen-free
- 20-pin STQFN: 2mm x 3mm x 0.55mm, 0.4mm pitch
Comparison
Applications
Applications
- Outdoors electronics
- Factory automation
- E-Bikes
- Power electronics
- EV charging stations
- Personal computers and servers
- Motor drivers
- High-voltage MOSFET drivers
- LED matrix dimmers
Documentation
= Featured Documentation
Log in required to subscribe
|
|
|
|
|---|---|---|
| Type | Title | Date |
| Datasheet | PDF 2.81 MB | |
| Brochure | PDF 4.80 MB 简体中文 | |
| Device Errata | PDF 705 KB | |
| White Paper | PDF 393 KB | |
4 items
|
||
Design & Development
Software & Tools
Software & Tools
| Software title
|
Software type
|
Company
|
|---|---|---|
| Go Configure™ Software Hub Go Configure Software Hub provides development support for a variety of products, including GreenPAK configurable mixed signal matrix and ForgeFPGA™ devices.
|
Software Package | Renesas |
1 item
|
||
Boards & Kits
Boards & Kits
GreenPAK Advanced Development Board
The GreenPAK Advanced Development Board provides full programming, emulation, and testing functions for the GreenPAK devices - for use with SLG46xxxX-SKT /...
Featured Documents:
Available on Lab on the Cloud
Use our PC-based GUI to instantly start configuring and testing designs in our virtual lab, no physical board needed.
GreenPAK Lite Development Board
The GreenPAK Lite Development Board provides full programming, emulation, and testing functions for GreenPAK devices, working in a pair with the Go Configure™ Software...
Models
ECAD Models
Schematic symbols, PCB footprints, and 3D CAD models from SamacSys can be found by clicking on products in the Product Options table. If a symbol or model isn't available, it can be requested directly from the website.
Processing table
| TQFN | 20 | 17 | -40 to +105°C | Tape & Reel | Get Samples, |
Tips for Using This Parametric Table:
- Hide Filters button in header: Collapse or expands filters
- Column sort buttons in header: Sort Column alphabetically / numerically descending or ascending
- Reset button in header: Reset all filters to the page default
- Full Screen button in header: Expand the table to full screen view (user must close out of full screen before they can interact with rest of page)
- Export button in header: Export the filtered results of the table to an Excel document
- Filter parts search bar in header: Type to filter table results by part number
- Hide column button in column headers: Select to hide columns in table
- AND / OR toggle switches in header: Toggles the logic of this particular filter to be “AND” or “OR” logic for filtering results
- Multiselect checkboxes at beginning of each row in table: Select these checkboxes to compare products against each other
- Document icon next to product name in row: View the featured document for this product
- Chip icon next to the right of the document icon in row: View the block diagram for this product
- Cart icon to the right of the chip icon: Indicates that samples are available for this product
Videos & Training
GreenPAK Configurable Mixed-signal IC Introduction
Video List