AnalogPAK SLG47011 Evaluation Board
The SLG47011V-EVB evaluation board is used to show the superior performance of the SLG47011V programmable mixed-signal matrix as a small, low-power component used in...
Overview
Description
The SLG47011 provides a small, low-power solution for commonly used analog-to-digital conversion and mixed-signal functions. A flexible data acquisition system used in conjunction with configurable logic provides a way to implement a wide variety of functions with minimal cost. The user may create a circuit design by programming the one-time programmable (OTP) Non-Volatile Memory (NVM), to configure the interconnect logic, the macrocells, and the IO pins.
Features
- 14-bit, 1Msps SAR ADC
- Sampling up to Four Analog Channels
- 14-, 12-, 10-, 8-bit Selectable Resolution
- Output Options: Parallel, I²C, SPI
- Programmable Gain Amplifier
- 1x to 64x Gain Selection
- Differential, Single-Ended Modes
- MathCore
- Multiplier, Adder, Subtractor, Shifter Options
- Four Independent Data Buffers
- Buffer Length up to Eight 16-bit Words
- Oversampling Mode (Increasing ADC Resolution)
- Moving Average Mode
- Counter Capture Mode
- 4096 Words x 12-bit Memory Table Macrocell
- Full Range Mode or Two Ranges Mode
- ADC Data Linearization or Any y = F(x) Function
- ADDR-to-DATA/Storage Modes
- 16-bit Multichannel Digital Comparator (MDCMP)
- Sampling up to Four Independent Channels
- Static or Dynamic Threshold
- Hysteresis Option for Each Channel
- PWM Macrocell
- 12-bit Resolution
- Dynamic Duty Cycle Change (up to 4096 Duty Cycle Value)
- Width Converter Macrocell
- 12-bit Parallel Data Output
- Optional 12 x 1-bit, 3 x 4-bit, 2 x 6-bit Output
- 12-bit 333ksps Digital-to-Analog Converter
- Selectable Current Source
- Integrated Voltage References (VREF)
- High-Speed Analog Comparator
- Configurable Hysteresis and reference
- Eighteen Combination Function Macrocells
- Two 2-bit LUT or DFF/LATCH Macrocells
- Eight 3-bit LUT or DFF/LATCH with Set/Reset
- Six Selectable DFF/LATCH or 3-bit LUTs or Shift Registers
- Two 4-bit LUT or DFF/LATCH with Set/Reset Macrocell
- Fourteen Multi-function Macrocells
- Ten Selectable DFF/LATCH or 3-bit LUTs + 12-bit Delay/Counters
- Two Selectable DFF/LATCH or 4-bit LUT + 16-bit Delay/Counter/FSM
- One Selectable DFF/LATCH or 3-bit LUTs + 12-bit Delay/Counter/FSM
- 12-bit Memory Control Up/Down Counter
- Communication Interfaces
- I²C Interface
- SPI Interface
- Programmable Delay with Edge Detector Output
- Deglitch Filter or Edge Detector
- Two Oscillators (OSC)
- 2kHz/10kHz Oscillator
- 20MHz/40MHz Oscillator
- Analog Temperature Sensor
- Power-on Reset (POR) with CRC
- Read Back Protection (Read Lock)
- Power Supply: 1.71V to 3.6V
- Operating Temperature Range: -40 °C to 85 °C
- RoHS Compliant/Halogen-Free
- Available Package: 16-pin STQFN: 2.0mm x 2.0mm x 0.55mm, 0.4mm pitch
Comparison
Applications
- Consumer Electronics
- Handheld and Portable Electronics
- Industrial Automation and Process Control
- Personal Computers and Servers
- PC Peripherals
- Battery Voltage and Current Monitoring
- Power Monitors
Design & Development
Software & Tools
Software & Tools
| Software title
|
Software type
|
Company
|
|---|---|---|
| Go Configure Software Hub Go Configure Software Hub provides development support for a variety of products, including GreenPAK configurable mixed signal matrix and ForgeFPGA™ devices.
|
Software Package | Renesas |
1 item
|
||
Sample Code
Boards & Kits
AnalogPAK SLG47011V Development Kit with Socket Adapter
The SLG47011V-SKT is a socket adapter kit for use with the SLG4DVKADV GreenPAK Advanced Development Board or SLG4DVKLITE GreenPAK Lite Development Board. The...
Featured Documents:
AnalogPAK SLG47011 20-pin DIP Prototyping Board
The SLG47011V-DIP 20-pin DIP Prototyping Board is perfect for breadboarding and fast prototypes. It requires the DIP Adapter (SLG4SA-DIP) to use it with the GreenPAK™...
AnalogPAK SLG47011V USB Power Demonstration Board
The SLG47011V demonstration board is a compact, easy-to-use, USB Type-C powered hardware tool for measurement of voltage, current, power, and temperature. The SLG47011...
Featured Documents:
GreenPAK Advanced Development Board
The GreenPAK Advanced Development Board provides full programming, emulation, and testing functions for the GreenPAK devices - for use with SLG46xxxX-SKT /...
Featured Documents:
Available on Lab on the Cloud
Use our PC-based GUI to instantly start configuring and testing designs in our virtual lab, no physical board needed.
GreenPAK Lite Development Board
The GreenPAK Lite Development Board provides full programming, emulation, and testing functions for GreenPAK devices, working in a pair with the Go Configure™ Software...
GreenPAK Introduction Kit Lite
The SLG4DVKLITEINTRO GreenPAK™ Introduction Kit is perfect for customers starting new development with the GreenPAK programmable mixed-signal products.
GreenPAK...
Featured Documents:
GreenPAK DIP Adapter for GreenPAK Advanced Development Board
The GreenPAK DIP Adapter for the GreenPAK Advanced Development Board allows using the SLG46xxxV-DIP and SLG47xxxV-DIP Proto boards with the GreenPAK Advanced...
GreenPAK DIP Development Board
The GreenPAK DIP Development Board is perfect for breadboarding and fast prototyping. It works in tandem with the GreenPAK Designer software (built into Go Configure™...
Featured Documents:
GreenPAK Serial Debugger Board (GSD)
GreenPAK Serial Debugger (GSD) device can be used for programming GreenPAK products with multiple-time Non-Volatile Memory (NVM) or for configuring the interconnect...
Featured Documents:
Models
ECAD Models
Schematic symbols, PCB footprints, and 3D CAD models from SamacSys can be found by clicking on products in the Product Options table. If a symbol or model isn't available, it can be requested directly from the website.
Processing table
| STQFN | 16 | -40 to +85°C | Get Samples, |
Tips for Using This Parametric Table:
- Hide Filters button in header: Collapse or expands filters
- Column sort buttons in header: Sort Column alphabetically / numerically descending or ascending
- Reset button in header: Reset all filters to the page default
- Full Screen button in header: Expand the table to full screen view (user must close out of full screen before they can interact with rest of page)
- Export button in header: Export the filtered results of the table to an Excel document
- Filter parts search bar in header: Type to filter table results by part number
- Hide column button in column headers: Select to hide columns in table
- AND / OR toggle switches in header: Toggles the logic of this particular filter to be “AND” or “OR” logic for filtering results
- Multiselect checkboxes at beginning of each row in table: Select these checkboxes to compare products against each other
- Document icon next to product name in row: View the featured document for this product
- Chip icon next to the right of the document icon in row: View the block diagram for this product
- Cart icon to the right of the chip icon: Indicates that samples are available for this product
Videos & Training
SLG47011 AnalogPAK Programmable Mixed-Signal Matrix Overview
The low-cost, low-power SLG47011 is an AnalogPAK™ programmable mixed-signal matrix with a 14-bit ADC and analog features.
Video List
